Product Parameters
| Specifications |
| Model | 3CM-5BG |
| Capacity※1 | 120 bags/hour |
| Set weight | 20~30kg/ bag |
| Bag type | Paper |
Bag size
※２ | Width of empty bag | 380 to 460 mm |
Length of empty bag | 750 to 950 mm |
Air consumption | 300NL/min |
Power requirements | 1.5kW |
| Machine Weight | about 0.7t |
Product size*The dimensions in the picture vary depending on the specifications。
Outline dimensional drawing |
{pboot:if('①FeederPlace bags neatly with top opening facing front. The magazine holds approximately 50 bags.②Pickup UnitBags are picked up one at a time, turned 90 degrees, and set on the filling station.③Clamping UnitEach bag is clamped at both edges with 30mm wide clamps. Clamping is checked to insure accuracy.④Bag Opening UnitSuckers pull open the bag mouth and then release using a vacuum generator. Timing is adjusted with the pickup and takeout. The clamps shift inward when the bag mouth is opened by vacuum.⑤Filling StationThe specially designed expansion spout (conventional hopper that is turned 90 degrees) fills the product. The clamps stretch out to spread the gussets after filling.⑥Weighing MachineThe clamp and filling station is suspended on three load cells. Auto zero adjust is performed automatically with empty bags.⑦Carrier Table and Bottom TapperThe carrier table moves to the hopper position as filling starts. The bottom tapping plate supports the bag from below and taps the bag to facilitate settling.⑧Bag FormerAfter the gussets are fully unfolded, the bag mouth is neatly formed and held between press bars on the hopper and the carrier table.⑨Bag GripperThe carrier table transports the bag to the sewing head while the bag is firmly gripped from both sides.⑩Sewing Machine (DS-7C）The sewing head starts operation upon detecting an approaching bag. The grippers release the bag. The sewing head stops upon detecting the trailing edge of the bag.⑪DischargeThe carrier table stops in a preset position. The bottom tapper inclines and the bag slides off the machine.'!='')}
Product Details
{pboot:2if(''!='')}
{2else}
①Feeder
Place bags neatly with top opening facing front. The magazine holds approximately 50 bags.
②Pickup Unit
Bags are picked up one at a time, turned 90 degrees, and set on the filling station.
③Clamping Unit
Each bag is clamped at both edges with 30mm wide clamps. Clamping is checked to insure accuracy.
④Bag Opening Unit
Suckers pull open the bag mouth and then release using a vacuum generator. Timing is adjusted with the pickup and takeout. The clamps shift inward when the bag mouth is opened by vacuum.
⑤Filling Station
The specially designed expansion spout (conventional hopper that is turned 90 degrees) fills the product. The clamps stretch out to spread the gussets after filling.
⑥Weighing Machine
The clamp and filling station is suspended on three load cells. Auto zero adjust is performed automatically with empty bags.
⑦Carrier Table and Bottom Tapper
The carrier table moves to the hopper position as filling starts. The bottom tapping plate supports the bag from below and taps the bag to facilitate settling.
⑧Bag Former
After the gussets are fully unfolded, the bag mouth is neatly formed and held between press bars on the hopper and the carrier table.
⑨Bag Gripper
The carrier table transports the bag to the sewing head while the bag is firmly gripped from both sides.
⑩Sewing Machine (DS-7C）
The sewing head starts operation upon detecting an approaching bag. The grippers release the bag. The sewing head stops upon detecting the trailing edge of the bag.
⑪Discharge
The carrier table stops in a preset position. The bottom tapper inclines and the bag slides off the machine.
{/pboot:2if}
{else}
{/pboot:if}
